Tag Archives: schematic symbol

What’s So Difficult about Diodes?

Posted on by

A diode can be put on a a PCB in one of two ways. It’s only got two pins (usually — see, I already have a caveat). I’ve written about them a few times before. I’ve got a sampling of those posts here. But first,

Good marking:

 

 

 

 

Bad marking:

 

 

 

 

The diode schematic symbol is always a good choice. If there isn’t room for that, “A” for anode or “K” for cathode work well too. Why “K”, and not “C”, you may ask? Because “K” kan’t be konfused with a capacitor.

Okay. Enough ranting for now. Just use the diode schematic symbol, “A”, for anode, or “K”, for cathode; and always look at the data sheet for the exact part number.

Duane Benson
1 cricket per chip

http://blog.screamingcircuits.com

LEDs: Seeing Double

Posted on by

Like I do so often, I’m being a bit redundant. While I’m all for stamping out and eliminating redundancy, this is redundancy with a purpose (not a porpoise). Not long ago, in a galaxy not far away, I blogged about annoyances in surface mount diode polarity markings. You can read that here.

I’ll wait.

Messy isn’t it? Well, after reading that blog, someone asked me about dual diodes. For some reason, I can’t seem to find the page covering dual diodes in my IPC book, but that’s not the important part. What is important is the way the diodes are marked on the PC board.

We do ask for centroid data which, in theory, contains the component rotation. That would be cool except that we find that far too often, the zero degree orientation (and the rotation from that) differs from the standard. That, and there are seemingly half a dozen or so standards.

Since LEDs don’t work too well backwards, we really would like to see everything marked in a non-ambiguous way in silk screen (or in an assembly drawing if you don’t have silk screen). A “cathode bar” won’t work because it could be a bar indicating the cathode or negative. The cathode isn’t always negative, especially when looking at TVS or Zener diodes.

Mimicking the diode markation pattern printed on the part may not be secure either. Read that article I linked to right at the start of this blog. What if you put silkscreen down to match one of those LEDs but ended up buying the other one? That’s exactly what I did myself. Trust me. It just leads to disappointment and possible soldering iron induced finger burns.

So what is the answer, and why am I talking about single LEDs and TVS diodes when the blog is about dual LEDs? Well, the answer is the same. The best way to communicate the desired polarity of an LED or any kind of diode is with a mini version of the schematic symbol. It doesn’t matter if it’s a single LED, dual LED, Schottky, Zener or whatever kind of diode. The schematic symbol is the clearest way to go.

Led marking

The diode footprint has the manufacturer’s polarity marking, but I don’t care. I still put the diode schematic symbol next to it. If you don’t have room for silk screen, put it in an assembly drawing. You won’t regret it.

Duane Benson
And they called him Flipper…

http://blog.screamingcircuits.com/

More Beagle CAD Paws

Posted on by

Continuing on from my last post …

As I said, I do everything I can to avoid reusing the package footprint when adding the the parts library in Eagle CAD. The schematic symbol can be a different story though. It still takes a lot of caution, but it’s less risky (in my opinion) than reusing the package footprint.

Eagle v.  6 made some improvements in the way copy and paste works. It’s still a little different from your typical word processor, but it’s not that difficult.

Eagle footprint menu bar 3 buttonsBut before I get to that, I want to mention one item that caused me a fair amount of confusion early on. And that’s the way all of this fits together. There are three buttons you will need to worry about. From left to right in the green oval are; the device, the package footprint, and the schematic symbol. In my last post, I pointed out the package footprint and today I’m talking about the schematic symbol.

Really, you only build the footprint and the schematic symbol. Then you connect the two up to create the devices. And, you can build the footprint or schematic symbol in either order, but you have to have them both before the last step (the icon in the green oval with four little AND gates).

If you’re using a chip that comes in a couple of different packages (e.g., DIP28, SOIC28, TSSOP28) you most likely only need to make one schematic symbol. You can make the multiple footprints and connect them up in the device section as different variants of the same part.

There are a few exceptions though. Sometimes QFN, QFP or BGA parts will have a few extra pins. In those cases, it’s generally better to create a different schematic symbol.

Duane Benson
This solder paste stencil glows blue when goblins are around

http://blog.screamingcircuits.com/